0006 リザードン02〔ポケモン折り紙〕リザードン02の作り方/みるかなた

Basic Folding

1 Fold the bottom corner to meet the top corner.
2 Make a crease and return it to its original position.
3 Rotate the paper 90 degrees, fold the other pair of corners together, make a crease and return it to its original position.
{Flip}
4 Rotate the paper 45 degrees and fold the bottom edge to line up with the top edge.
5 Make a crease and return it to its original position.
6 Rotate the paper 90 degrees and fold the other pair of edges together.
7 Hold the crease ▲ made in step 6 with your fingers and fold gently from both sides together.
8 Let the paper naturally fold along the creases to form the shape of 9.
9 A basic square is created.

{Enlarge image}
10 Change the top and bottom positions.
With the opening facing downwards, fold the bottom left and right edges to meet the crease in the middle.
11 Make a crease and return.
12 Fold the top at the point where the crease made in 11 intersects with the top left and right edges.
13 Make a crease and return.
14 While opening the front paper upwards, fold the left and right edges inward along the crease made in 11.
15
16
{Flip}
17 Make creases on this side in the same way as 10 and 11.
18 Fold in the same way as 14, 15 and 16 to form 19 and 20.
19
20 The basic fold is complete.

Charizard (No. 2)

0 Place the orange paper on the outside and the red paper on the inside, aligning the white sides of the backs of the papers, and fold both together. Initially, folding two sheets together is difficult, so fold one sheet once to understand the folding method before folding two sheets together.
1 Fold up to the shape of basic fold 20. Create the upper jaw. Fold the top front sheet downwards at the base.
2 Fold the bottom front sheet upwards at a position 10 mm below the base.
3 Mark the position of the fold on the center edge of the left and right sheets at the back, and return to the top.
4 First, fold diagonally from the marks made in step 3 to a position 10 mm to the left and right of the base. Next, fold upwards with a width of 10 mm from there. It will not be flat, and the edges will be raised.
5
6 Fold the top front sheet downwards at the base.
7 Make sure to crease the folds made in steps 4 and 5, and return to the top.
8.
Fold downwards at a point 7 mm above the crease.
10. Lightly crease the paper.

11　
12 Make sure to crease the paper firmly.
13 This is the shape of 12 slightly opened.
14 Make the nose and fangs. Open all the paper at the front of the top, and also open the paper on the left and right at the bottom to make the shape of 15.
15 Fold only the front sheet of paper backward along the crease made in 9 and tuck it between the sheets of paper.
16 Fold the second sheet of paper upward along the crease made in 10 and tuck it between the first and second sheets of paper.
17 Return the paper opened in 14 to the shape of 13.
18 Fold the nose as shown in 19 and 20.
(Enlarge the diagram)
19
20 The fangs are complete.

21 The upper jaw is complete.
22
｛Flip｝
23 Make the lower jaw. First, fold diagonally from 10 mm below the center base to 10 mm to the left and right of the base. Next, fold it up in a 10 mm width from there. Then, fold it in the same way as in Figure 4 to 22.
24 Once the upper and lower jaws are complete, make the horns. Fold the bottom left and right pieces of paper slightly diagonally in the middle fold and up at a position 10 mm below the base.
25 Fold the ends of the paper in the middle fold and tuck them between the pieces of paper.
26 The horns are complete.
27 Fold only the front piece of paper to the back.
28
｛Flip｝
29 Fold only the front piece of paper to the back.

30 Gently fold along the crease made in Figure 2, and slightly raise the upper jaw to open the mouth.
31 Charizard (No. 2) is complete.